With reseal and I assume pressure test, plus warranty on the work I don't think that's too bad.
Seiko now charge a whopping £90 for battery change and reseal..
Looks to be a simple enough job.. I probably wouldn’t trust high street for it… but there must be a less extortionate option from a competent watchmaker/repairer..?
Any recommendations?
Thanks, Steve
Sent from my iPhone using Tapatalk
With reseal and I assume pressure test, plus warranty on the work I don't think that's too bad.
I recently sent my Hydroconquest back to the mother ship for a battery change. It came back with new seals and pressure test and two years peace of mind for £73 including postage in a nice little travel case. I don't think £90 for a GS too bad.
Be brave . It’s a simple enough job with the correct tools . Cover the case back with transparent plastic to prevent scratching the case back when using case back remover . Once open you should be able to keep the gasket in place. The battery is in a separate compartment from the movement and is easily replaced with no risk of damage . The risk is nominal and you’ll save £90.
From one of our very own members
https://youtu.be/mIw3cMPZins
Cheers,
Ben
..... for I have become the Jedi of flippers
" an extravagance is anything you buy that is of no earthly use to your wife "
I’ve used https://onatelier.co.uk/ (.olli. on here) to do the battery on my SBGT241.
Would recommend him highly.
Omega currently charge £60 for the same job, £40 from my local watchmaker. Can’t remember what Rolex asked for an Oysterquartz battery change last time around, but GS seem to be pushing the boat out there. I know we have 10% inflation but everything seems to cost 50% more than it used to.
Have to smile at the term ‘reseal’, a somewhat grandiose term for refitting (or replacing) the caseback seal and refitting the caseback!
To be really thorough and avoid potential comebacks it makes sense to pressure test the watch, I usually take the movement out to do this as a safeguard against getting water into the watch ( wet tester used). If all’s well.
Can’t see anything too difficult about the Grand Seiko, £90 seems crazy to me.
This may be a stupid question but do Grand Seiko use special batteries for GS watches, or do they use the same batteries as in a standard Seiko?
When I enquired about a battery change at GS they advised the crown, case back seals etc were all changed and the watch wet pressure tested. It was then returned with a 2 year warranty.
I don't think the price is bad at all considering what's done along with the warranty.
Can't help but smile when people who spend thousands of pounds on a watch then quibble over £30 for a battery replacement (£60 is ok - £90 isn't?). It's like people who buy £50k+ cars and then fit the cheapest tyres that they can find when they need replacing.
£90 seems perfectly acceptable to me for a professional job that isn't required very often.
Hmm. Not sure. I stretched myself to get my GS. And that was second hand. It's the only way to get one. Do I think £90 is worth a battery change? No I don't. It's a 5 minute job. That's £450 an hour to take a case back off, replace battery then replace case back. Do they replace seals or lubricate? Who knows.
Can anyone reccomend a caseback tool please?
Also, where can I source the correct Seiko battery?
Sent from my SM-G950F using Tapatalk
https://www.amazon.co.uk/gp/product/B07K256DPC/
This was recommended on a thread back in November. I bought it and have used it several times. Definitely felt better than other 'cheapies' I've used.
I've no idea what the caseback on your GS looks like but hopefully suitable.
Sent from my Redmi Note 9S using TZ-UK mobile app
So this:
Any 3-pin tool like that posted above will work. The trick will be to get one bit a selection of tips, so that you can achieve a good fit to avoid marring.
Do they not grease the seal? Anyway probably generates chat because of the price.
Does anyone use these to remove the case back?
https://www.amazon.co.uk/Bergeon-800...a-799179746543
Think I would feel safer using one.
Also is there a recommend grease for the seals/gaskets and can you get the seals anywhere?
These are great for casebacks that have been tightened to a reasonable level ie not sealed down like Chernobyl Seiko diver casebacks, lol.
Sent from my Redmi Note 9S using TZ-UK mobile app
Also available from Cousins for a fiver!
Description states: Will not open very tight case backs
https://www.cousinsuk.com/product/su...ss?code=C51738
I’ve had a couple of Aqualands that I’ve had to put in a case holder and pop that in my vice to keep it still - allows a little downward pressure as I turn
5 minute job eh.
There's replacement of the battery, gaskets and a pressure test once done. I believe that the battery change is done at a service centre so there may be shipping charges involved. I also assume there's a warranty for the work done. So I have the option of attempting it myself and possibly damaging an expensive watch, or pay (possibly less than) the cost of a new tyre on my car and leave it to the experts.
It's professional as you're paying someone to do it and it's a skilled job, possibly not highly skilled. If you gave the watch to the average person in the street, do you think they could change the battery and seals (even with instruction) successfully without damage to the watch and pressure test it?
I agree. Having used a three prong "Jaxx" versus a simple two prong opener, the cheap Chinese blue ones, the two prong is more effective and safer.
I should point out, I've only used these to regulate inexpensive Vostoks, but the two prong was a lot easier to align and torx.
If I had a GS, personally I'd send it to Seiko for a battery change.
Have to agree; struggle to see how anyone could have difficulty using one of those personally, but then everyone has different abilities in different areas… hence why I mused earlier that £90 from Seiko might represent a value to some: if I thought for a picosecond I could damage a watch, I’d be handing over my money.
Ask Bry if he has a 6 point non marking opener that fits ? I use them all the while as they are my go to tool for case backs.