Bergeon tools are decent
I am looking for a tool to remove the case back of specifically Rolex Oysters, Sub, GMT, Sea Dweller et el
Can anyone recommend a suitable tool for the job?
Also any recommendations on general watch tinkering tool kit would be welcomed
Thanks
There are many ways to open a case back. The sticky ball method for example. You could also try blue tack around the circumference of the back and then push the bottom of a glass against it and rotate. Unless the case is really tight it should come off. Whatever you do, take care and don't scratch anything....
http://www.watchtool.co.uk/bergeon-6...ar-p-6516.html
That site has a pretty comprehensive selection
You need a caseback tool - a hand wrench would do, but a press type is better though much more expensive - and a set of Rolex dies. This one from Cousins maybe.
I`m a bit puzzled as to why the OP wants to open his Rolex?
Not something I`d advise a novice to do....and I`m guessing the OP's a novice by virtue of the questions.
As for sticky balls, yes they work on some casebacks but they won`t work on anything that's been done up tightly.
I bought a set of Rolex openers from ebay a couple of years back; they're reasonably OK but not top quality, they need using very carefully to avoid slipping/damage.
Paul
Last edited by walkerwek1958; 6th April 2015 at 12:50.
Bergeon 5700 with the bergeon adapter and Rolex dies. Then buy the rubber upper suction dies. These tools will allow you to open any screw cased watches from any make without the chance of marking them. Jaxa and other hand versions are unsafe and cause way more damage than good.
If you have shallow pockets then either try another hobby or buy the Chinese fakes of the above, just don't expect them to last long term.
Indeed - and is he aware of the need to pressure test the watch after the back has been off? Especially if he's talking about Submariners, Seadwellers, etc.
My fear with the Chinese fakes would be less about how long they might last, and more about how likely they are to damage the Rolex's caseback.
Is the Bergeon 2533 Watch Opener Tool Suction Case Opener any good?
http://www.esslinger.com/bergeon-253...ch-opener.aspx
Last edited by GrandS; 6th April 2015 at 14:09.
Yep good bit of kit, better than balls that people use as the end twists with torsion when used and therefore adds more force than a ball. Still only works on roughly half the watches I try it on, so by default all modern high water resistance watches go on the 5700 and old dust proof cases get the 2533.
All
Thanks for the replies. It was the Bergeon that I was thinking of, however as oppose to ask, "Is it any good" I preferred to leave the question open to encourage more replies ;)
I am fully aware of the implications of removing the case back, however in certain circumstances it is only way to ensure that the watch is indeed what it is being advertised as!
So I guess the reason you're taking the backs off is to verify watches are genuine? All the more reason to be sure not to damage the caseback....the conversation with the seller would'nt go well after you've marked his watch.
Sounds like the only safe bet is the expensive tools, and you'll need to open a lot of casebacks (and buy a lot of watches) to make it worthwhile.
Paul
Last edited by walkerwek1958; 7th April 2015 at 11:39.
As someone who will be receiving their first rolex soon I would be far to scared to do this!
If you open any watch, dont you need then to verify its water resistance? so not only one tool, but more. Hard to justify the cost if you are not a watchmaker.
Provided the caseback seal's in good condition and it's replaced carefully I would contend that you don`t need to test it's water resistance. However, it's a judgement call; O-ring caseback seals can assume an oval profile after being in place many years and sometimes they don`t go back in the same orientation. if the elasticity of the rubber has deteriorated you could then have a sealing problem. Best bet is to fit a new seal if you're in any doubt.
If I was selling a Rolex there's no way I`d allow anyone to take the back off, unless they were a repairer or an AD. Too much scope for it to end in tears.....and scope for the watch to lose it's water-resistance!
Paul
A 5700 Rolex dies and adapter plus a basic water resistance machine and you are running at a few thousand, you don't have to buy many to make it worthwhile.
How do you know the watches you are opening are water resistant to begin with? Even if freshly serviced and tested it is no guarantee. A small knock and the glass can stop being water resistant. Same with the crown and so on. You can't assume a watch is water resistant on receiving it.
I always test first unless doing a full refurb, as everything is replaced then anyway.