They took all the good stuff out of it a number of years ago thanks to health and safety. I have tried a few other brands but all hopeless. For smaller articles wrapping them tightly in a plastic bag keeps the fumes in and improves the performance.
It's absolutely useless Now, any suggestions for a paint stripper that works would be appreciated.
It used to be that if you splashed it on the back of your hand you knew all about it, I reckon you could bath in this stuff and not feel it
Last edited by adrianw; 27th April 2024 at 17:14.
They took all the good stuff out of it a number of years ago thanks to health and safety. I have tried a few other brands but all hopeless. For smaller articles wrapping them tightly in a plastic bag keeps the fumes in and improves the performance.
Starchem synstrip is very good if you can get it.
Would you like a jar of Uncle Alec's Chili Relish?
EU banned methylene chloride - key ingredient of the old version.
When you look long into an abyss, the abyss looks long into you.........
Time to get out the wire wool and apply some elbow grease
Have a look on YouTube as I seem to remember Roger Bisby of Skill builders did a test on this.
Fifa
Proper creosote went the same way as Nitromors. Now there's some wishy-washy alternative which has the same sticking power as watered down soy sauce.
As an apprentice 48 years ago the stripping of Shellac’s and old varnish surfaces was a job you did. I remember back then if you got some little flicks off the brush on to your bare skin it was hell. At the end of the day you looked like you had measles. As said it would not strip the skin of a rice pudding now. All to do with H&S changes back in 2008 I remember it well all my COSHE Assessments had to be changed for the Risk and Method Statements.
I found something pretty effective on aluminium castings, the Dirtkiller attachment on my pressure washer, it just eats paint, obviously there are a lot of things you mustn't point it at.
Vapour-blasting seems to be the new method, and you can find several people offering the service on a kind of 'paying hobby' status.
Have a search on Facebook Marketplace. I doubt you'd have to travel more then 50miles.
Not a lot of money and leaves the castings/components ready for a wipe down with acetone and painting/laquering.
Similar experience with Jeye's Fluid. Used to be a great mosskiller, even in very low concentrations.
Add Round Up to the list of “used to be good, now rubbish”
Creosote is still available from agricultural suppliers .
I was given the tip by an employee as it’s used in/on chicken buildings as it prevents “ chicken mite “ .
The only draw back is it’s in 25 litre containers , however my friends all have creosote treated sheds and fences .
Sent from my iPhone using TZ-UK mobile app
I bought in bulk at 18 quid for 25 litres at 15% juiced down 4 parts water to one part solution. (Walker Bros, Oldham)
You're right about it bleaching clothing/shoes out, no bother.
I brush it one my drive with a long hair soft sweeper, leave it 20-30 mins then rinse it off with a jet wash, looks like new on completion.
Would wrapping it in clingfilm assist?
+1 for sodium hypochlorite on driveway/patio
Sent from my CPH2415 using Tapatalk
Banned from domestic use in 2003 under EU biocidal products regulation due to environment and health issues (col tar based). Still available for commercial use (railway sleepers, telegraph poles, agricultural fencing). A further increase in the ban is coming in early 2005 except for railway sleepers and telegraph poles.
When you look long into an abyss, the abyss looks long into you.........
^^ 2025?
That is what I do with oven cleaner - brush it on to the sides and cover with cling-film. Way better as it stays in gel form.
for the oven roof - lay out alu foil, with cling film on top. brush the gel on to the oven roof and offer up the clingfilm/foil. drop the foil out and pat the clingfilm on to the surface.
The foil is just to support the clingfilm as you lift it into position.
Armillatox is now defunct - the product to go for moss, algae etc
Apparently it wasn't worth the hassle of going through the regulation.
B