crown screws down with just a 1/4 turn, can this be right?

[poppy]

As the title suggests, a watch i bought recently (breitling avenger chrono) has an issue, the crown does screw down but only with a quarter turn, can this be correct?

it felt far to small an amount so i sent it back to the seller (watchfinder) who so far have been excellent in dealing with it but they have said that it is fine as it screws down and maintains water resistance with just the small amount of screw down.

am i being fussy expecting it to screw down further or should i be happy with the fact that the watch functions perfectly other than this {small} issue?

[markosgr28]

This was the same with the breitling avenger chrono titanium I use to have. I asked the watch technician and told me that it was OK. Same with a Rolex precision I use to have.

It didn't feel right to me, too, especially in the CA, which is 300m WR.

[SplitSecond]

I had the same issue with a watch, though not a Breitling. Within a few months, there was no thread left to screw the crown down. So in my experience it's a sign of imminent need for replacement of either the crown, the tube, or both.

[rsykes2000]

Not having owned a Breitling CA, I can't comment on it directly, but any crown that only screws down a quarter of a turn (and has no clocking mechanism as well) would to me not be secure.

[walkerwek1958]

I haven`t got first-hand experience with this watch, but it sounds totally wrong to me. I`ve come across some watches that only screw one full turn, even with a new tube and crown, but most need around 1.5- 2 full turns.

Regardless of what Watchfinder say I would insist on this being rectified or I`d reject the watch. Replacing case tubes can be a difficult job; some repairers duck out of doing this if the crown will still screw down and retain water-resistance.

If this one's only managing one quarter turn, it'll fail shortly. That's my take on it.

Paul

[marcus fenix]

I know Watchfinder have a former senior Breitling man on their staff, but not sure if they are actually accredited and able to get parts? If they can then it's a cheap fix, otherwise they are probably reluctant to get it fixed as they will probably have to pay for a full service.

[Nealywheelie]

No it is not right, there should be about 4/5 complete turns. This is an issue that does occasionally occur with Breitling crown and tubes as they employ an internal as opposed to external thread. I would get back to Watchfinder immediately and tell them they are quite wrong. One quarter of a turn is no way able to withstand the pressure rating of the piece.

[poppy]

thanks for the speedy responses folks.

I was pretty sure that this would be the case. I have messaged WF and asked them to have their tech guys check again. If the still say it is fine I am probably left with 2 solutions:

1- accept the return provided there is some kind of written warranty with regards to the particular isssue of the crown.

2- ask for a refund

I honestly think i am going to have to go with option 1 but i am gutted, it is such a good watch!

[marcus fenix]

No it is not right, there should be about 4/5 complete turns.

Are you sure about that? 4 or 5 complete 360 degree turns? I have never seen any watch that can do that, maybe 4/5 "turns" of your thumb, but not full turns. Most I have ever seen is 2.5 whole turns.

[744ER]

No it is not right, there should be about 4/5 complete turns. This is an issue that does occasionally occur with Breitling crown and tubes as they employ an internal as opposed to external thread. I would get back to Watchfinder immediately and tell them they are quite wrong. One quarter of a turn is no way able to withstand the pressure rating of the piece.

The WR is not affected at all, since the gaskets are fitted in the crowns internal perimeter and just need to envelop the tube. Most all waterproof watches are still waterproof with the crown screwed out.

However, a quarter turn is too little, the crown thread is most likely stripped (sometimes its the tube but more often the crown in my experience).

You need to request a new crown/tube fitting or refund.

[StuartGR]

I haven`t got first-hand experience with this watch, but it sounds totally wrong to me. I`ve come across some watches that only screw one full turn, even with a new tube and crown, but most need around 1.5- 2 full turns.

Regardless of what Watchfinder say I would insist on this being rectified or I`d reject the watch. Replacing case tubes can be a difficult job; some repairers duck out of doing this if the crown will still screw down and retain water-resistance.

If this one's only managing one quarter turn, it'll fail shortly. That's my take on it.

Paul

As Paul will testify, I had this problem with my Omega Seamaster (which he expertly sorted for me!) and I certainly would not be confident of the longevity of the crown/tube as is.

SGR

[RobDad]

It's clearly not right - I'd imagine the threads are partially stripped and its only a matter of time before they go completely. Bearing in mind their stupid attitude to customer service I'd get a refund and walk away to be blunt.